Blind Carving part 4. New sculptural wood carving from a wooden pallet. Finished

Blind Carving part 4.   Finished 

New sculptural wood carving made from a wooden pallet 

 

 

Finished with clear wax

 

 Brown wax makes it look less grey and warmer

 

 

The finished blind carving, hung on my kitchen wall.

This is the finished blind carving that I made from an old wooden pallet.

As you can see it turned out OK considering how bad the wood was. All the sections married up and they match well, which was a surprise as each piece was carved blind from each other.

You can also see how the wood reacted with the iron oxide vinegar mix and also how the brown wax made it look warmer.

Now its time to plan another project, so if anyone has any suggestions, please feel free to leave in the comments.

Blind Carving part 3. New sculptural wood carving from a wooden pallet

Blind Carving part 3.  

New sculptural wood carving from a wooden pallet

 

I am glad to say that I got the blind carving project finished, and considering the materials and tools I used, I am very happy with it. Before I go any further into describing how I finished the project, I would like to show you some of the carving tools I used and also ones that I just could not find at the time.

 

I went up into the loft today and found some of my carving chisels, the ones I didn’t use on this piece. I do have a few more, but sill need to locate them.

These are two Ashley Iles chisels that I bought when I was still an apprentice in 1989. They cost me, I think, about £18-£22 each, which works out at €22.86-€27.94 in Euros. When I bought them, they were reasonably priced at the time and I also got a trade discount from the tool shop I bought them in. They are fantastic chisels and came already sharpened, honed and ready to use. They also keep sharp when in use.

 

Now in comparison, this is a full set of 12 carving chisels that I bought in Lidl in 2012. They cost me €16 for the whole set which is an average on €1.34 each as compared to between €22.86-€27.94 for just one chisel. In many ways it seems a no brainer that the Lidl woodcarving chisels I bought a few years ago are good value, which indeed they are. But I have already spent about 7 or 8 hours, grinding, sharpening and honing them, and even with all that time I still haven’t been able to get them even a fraction as sharp as the Ashley Ilse chisels. When I can get them sharp, they just don’t hold a keen edge as the tool steal is too soft. In saying that, they are an OK starter set for anyone that is willing to put the work into grinding, sharpening and honing.

 

So back to the blind carving project.

I was able to get the nine sections of the coin finished and as I did each piece, I stained them with the iron oxide, vinegar mix. 

 

I then put a coat of wax on as each piece dried and am glad to say it looks OK.

As all the sections are separate pieces, I had to join them up together. I used MDF flooring to make a back and used hot melt glue to stick the carving on it. Although it made the carving sturdy, it also made it very heavy and I think the weight would have been too much to hang it on a normal domestic wall. I decided to take the MDF off and use an old curtain liner as a backing. So I cut the curtain liner into strips and then glued and stapled it to the back of the carving. Once this had dried, I then glued the rest of the liner over the whole back, which covered the staples and made it all look neater. I then put some picture hanging wire on the back and it was almost finished and ready to hang on the wall.

I felt that the carving looked a bit grey, so I put some brown wax on and buffed it off when it dried. To be honest, I now feel that it may have looked better before the brown wax went on, although the brown does make the finished piece look warmer.

 

So this is the finished piece that was made out of a wooden pallet.

I know it is not perfect, but I do think the imperfections add to overall look. As you can see, not all the pieces match up and some of the wood has started to warp and crack. I have to say I am very happy with it and for the first time since 1997, I feel like doing wood carving again. The reason I say 1997 is because that is when I made my first and up until now, my last carving. Now that's another story that I will talk about some day, and the reason my good carving chisels were in my loft.


Thank you for reading my blog and please feel free to make a comment if you wish.

 

Blind Carving part 2 New sculptural wood carving from a wooden pallet

Blind Carving part 2     New sculptural wood carving from a wooden pallet

So I worked out that I would be able to do the whole carving using 9 lengths of the wooden pallet. This would give me a good amount of wood to make my coin a nice big size. As it was going to be a blind carving, each piece will look different and it may not even match with the other pieces, which I think will look good as I am sure the wood is going to warp and crack. The other thing about this piece is I am not using my good carving chisels, but using some really cheep ones that cost €16 from Lidl. In truth, I only bought them because they were €16 for the full set from Lidl. They look really good, but it is almost impossible to sharpen them as the blade steel is way too soft and also they had to be ground down which took about 7 hours or more. I also used my normal chisels and a small Bosch router that I bought years ago. The router is fantastic to get rid of the bulk of the waste.

I took the piece of wood off and carved the section. When I was finished I put the wood back but found this to be tedious, so I started doing each piece and laying them to each other as you can see in the last photo.

Soon the carving came together and it was almost finished. Once I finished each piece, I stained it with a mixture of vinegar and steel wool that dissolved in the acid of the vinegar. This mixture will react to the tannins in the wood and make it darker, depending on the wood itself. As you can see, one of the sections went a dark blue gray colour.

So this is it almost finished. You can see some of the places the nails and tacks were, and how the vinegar mix reacts with the tanins in the wood and leaves it looking darker. Each piece is slightly different and they don’t fully match up, which is kind of what I wanted. So the next post, I will show how I will finish the sculpture.